Servo Futaba S3270SV 3.0kg.cm 0.11s/60° MG S.BUS2

Product detailed description

Powerful digital HV micro servo with coreless motor and ball bearings for versatile use. S.BUS and S.BUS2 support. Power supply 5.0-8.4V. Thrust 2.3kg.cm, speed 0.13s/60° at 6.0V, thrust 3.0kg.cm, speed 0.11s/60° at 7.4V. Weight 16.2g.

Strong and fast programmable digital S.BUS2/S.BUS micro servo with metal gears and output shaft mounted in two ball bearings with increased supply voltage for 450 helicopter gyrus boards, smaller electric model aircraft, larger gliders and motor gliders. For perfect cooling, the middle part of the case is made of aluminum heat sink.

S3270SV can be connected to the S.BUS 2 (serial bus with bidirectional communication) or S.BUS (serial bus with unidirectional communication) receiver outputs or can function as a classic servo connected to the channel (PWM) output of the receiver.

Using the CIU-3 USB interface and the S-Link PC program or a Futaba transmitter equipped with the S.BUS servo setting function, you can program a whole range of servo parameters (speed, deflection size, neutral, overload protection, soft start, etc.). Setting the channel for operation on the S.BUS2/S.BUS bus is possible only with the help of the transmitter.

Increased supply voltage 6.0-7.4 V.

What is S.BUS2/S.BUS

• S.BUS – Futaba serial bus with unidirectional communication allowing control of servos, regulators, switches, gyros and other compatible RC devices connected to a single S.BUS output port of the receiver.
• S.BUS2 – Futaba serial bus for bidirectional communication allowing (like S.BUS) control of servos, regulators, switches, gyros and other compatible RC devices connected to a single S.BUS2 output/input port of the receiver. In addition, it allows to connect telemetry sensors and transmit data from them through the receiver for display on the transmitter; from some S.BUS2 servos it is possible to transmit information about operating current, temperature or angle of the servo output lever to the transmitter.

Unlike classic RC sets, the S.BUS(2) system uses serial data communication to transmit control signals from the receiver to the servo, gyro or other device. This data contains commands such as "move servo channel 3 to 15 degrees, move servo channel 5 to 30 degrees" for multiple devices. S.BUS(2) devices only execute commands belonging to their own set channel. For this reason, it is possible to connect several servos to the same signal cable, while setting and controlling them individually as needed. The servo identification code (ID) is used for this. The ID can be found on the sticker on the servo box.

The S.BUS2 servo can be connected to both the S.BUS2 and S.BUS ports of the receiver. Its function is determined by setting the channel in the servo memory (it is done using the programming interface of the Futaba transmitter, the SBC-1 programmer or the CIU-3 USB interface with the S-Link PC program - for some servos, the channel can only be set using the transmitter).

The S.BUS2 servo connected to the channel output of a classic receiver (PWM) works like a classic servo. Its movement is determined by the signal in the receiver channel it is connected to. The settings of the programmable servo functions remain in effect.

Servo size - Micro
Servo type - Digital
Thrust at 6.0 V [kg/cm] - 2.3
Thrust at 7.4 V [kg/cm] - 3
Speed ​​at 6.0 V [s/60st.] - 0.13
Speed ​​at 7.4 V [s/60st.] - 0.11
Servo gears - Metal
Ball bearings - 2×
Highvoltage - Yes
Power supply [V] - 5 - 8.4
Length [mm] - 23
Width [mm] - 12
Height [mm] - 29
Weight [g] - 16.2
Designed for - Airplanes, Helicopters, Road cars, Off-road cars, Sailboats, Boats
S.BUS - Yes
S.BUS2 - Yes
SR mode - No