Amewi RC Hyper Go Lancia Delta HF Integrale Rallye/Drift 4WD 1/14 RTR

Product detailed description

RC model of the rally/drift car Lancia Delta HF with licensed Martini Racing body.

The 2845 3700KV brushless electric motor provides propulsion and distributes power to all four wheels via robust metal drive shafts. Integrated CVD shafts are mounted on ball bearings and ensure power transmission to the high-grip rubber tires (on-road or off-road) or drift tires that are included in the package. The chassis, gears and differentials are made of metal.

For optimal control and fine-tuning, the model has integrated metal shock absorbers with adjustable oil pressure and a ride stabilization system (gyro). The built-in 45A ESC controller allows for sensitive response during acceleration and LED lighting with different modes allows driving even in poor light conditions. The digital 17g steering servo also ensures precise cornering control and stability of the model.

The package also includes a polycarbonate cover that protects the internal electronics from dust, moisture and other dirt. The model is powered by a Li-Ion 2000mAh/7.4V battery, which allows a driving time of up to 12 minutes.

Features:

• Licensed Martini Racing body
• High-quality metal chassis
• Can be used for road, off-road and drift racing.

Other features:

• RTR version including remote control, battery and charger
• LED lighting
• 4WD drive with CVD drive shafts
• Dust protection cover
• Polycarbonate chassis cover
• Adjustable metal oil shock absorbers

Technical data:
Scale: 1/14
Length: 320 mm
Width: 153 mm
Height: 115 mm
Weight: 1256 g including battery
Wheelbase: 190 mm
Front track: 132 mm
Rear track: 132 mm
Ground clearance: 15 mm
Front wheels: Outer diameter/width 55/20 mm
Rear wheels: Outer diameter/width 55/20 mm
Rim diameter: 42 mm
Gearbox: Metal
Brake: Electronic
ESC controller: Brushless ESC 45A
Motor: Brushless 2845 3700KV
Steering servo: Digital 17g
Battery compartment dimensions: 87x37x30mm
Battery: Li-Ion, 2S 7.4V 2000mAh T-DEAN/JST 68x36x16mm, 97g
Running time: 10-12min
Maximum speed: approx. 40 – 45 km/h
Remote control: 2.4 GHz, 4-channel
Range: 100 – 150 m
Charger: USB charger
Charging time: approx. 240 min

Package contents: RC model, remote control, drive battery, USB charger, drift tires, off-road tires, cooling fan for ESC controller, stickers, wheel wrench, EN/DE manual

Run-in of the new electric motor
New model with engine, needs to be run in first. Before starting to use the DC electric motor, it is definitely recommended to run it. Some manufacturers require it as a condition for recognizing a possible engine claim. The purpose of the run-in is to seat the rotating parts well, smooth the friction surfaces of the contacts, and grind the carbons into the correct shape. The current enters the motor on the commutator surfaces using the so-called carbons, which may not have a perfectly adapted shape from production. If the new motor is loaded to the maximum without a previous run-in, the commutator surface or the carbons may be damaged due to large "sparking". The run-in will allow the carbons to settle on the commutator as perfectly as possible. Thus, the carbons will wear out less and last longer.

Electric motor run-in procedure:
-If you have a new RC model car or boat in which the engine is already mounted, proceed as follows. Place the model on the mat so that the wheels rotate above the surface. Let the engine run at the lowest possible speed for at least 20-30 minutes. You can then drive the model for 20-30 minutes at a lower speed and gradually increase the speed. Drive the model at full power only after the run-in phase has passed.

-If you have a new engine that has not yet been installed in the model, you can do the run-in in the traditional, proven way by immersing it in water. Connect the motor to the ESC controller and lower it by the cables vertically down into a container of clean water. Start the engine at low speed and let it run for 10-15 minutes. Then you can gradually increase the speed for a few minutes up to the maximum. finally, take the motor out of the water and let it run for a while to blow the water out of the motor. You can mount a run-in engine in the model and you can immediately drive at full power. You don't have to worry about the engine submerged in water. It will work normally and the water will cool it during the run-in. In addition, it washes out carbon particles during grinding (the water visibly darkens).

Protection against overheating of the electric motor:
Since the stator is made up of permanent magnets, it is good to know that these magnets gradually lose their "power". However, temperature also has a big impact. Each electric motor heats up during operation and can reach a temperature of 60°C (therefore, the motor must never be touched with bare hands after driving!). However, if the engine is not cooled or cooled insufficiently, or if it is driven for a long time at maximum speed, it may overheat and thus weaken the magnets. Even after cooling down, the engine will no longer reach its previous performance. Of course, other parts of the engine can also be damaged by high heat. It is therefore advisable to change the load mode, or to drive with two smaller accumulators with a break for replacement and cooling, rather than with one large-capacity one for a long time at full power.

Electric motor replacement, tuning:
If you decide to replace the electric motor in this model, pay attention to the following recommendations.
The new motor should be of the same type (size), have the same number of turns and the same supply voltage value as the original one. That way, you will be sure that the model will retain its original driving characteristics.
If you are planning a tuning motor, first of all, check whether the original ESC controller in the model will be able to work with the tuning motor, in order not to burn the ESC controller, or to prevent the ESC-motor system from working. When tuning a motor, it is usually necessary to replace a pinion with a different number of teeth.

WARNING! This RC car is not a toy, but a more sophisticated, functional model that behaves very much like a real car. Due to its realistic parameters, if it is not properly assembled and operated, it can cause you injury, or injure the viewer, or damage property. The model is intended for driving in a large room or outside on a dry surface. Driving in water, in snow, in puddles, mud, sand, in tall grass without appropriate waterproof treatment can cause damage to the electronics of the model. Driving on public roads and other places (e.g. parking lots) with car traffic is prohibited. Do not drive in thick grass, you will overheat or burn the engine!
This model requires regular maintenance, by disassembling it correctly according to the service manual, you will not lose the warranty.